SOLAR PANEL 10W
Order Code #10-004

12V 10W; 367x310 x 18mm

EFFICIENT Operation

Robust Construction; Aluminium Frame

SOLAR PANEL 20W
Order Code #10-005

12V 20W; 655x305 x 18mm

DOUBLE the Output

Robust Construction; Aluminium Frame

TRANSFORMER 15V AC 4amp
Order Code #10-050

2-core Lead

Fully IP-Rated

Durable Construction; External Rated

Able to be safely extended on Low-Voltage lead

Suits 12V 'AC' DIY Kits

TRANSFORMER 24V AC 4amp
Order Code #10-053

2-core Lead

Fully IP-Rated

Durable Construction; External Rated

Able to be safely extended on Low-Voltage lead

Suits 24V 'AC' DIY Slider Kits

BATTERY, 12V 7aH
Order Code #10-008

Enclosures available to house  multiple Batteries

IDEAL for Backup Use

SLA - Sealed Lead Acid Construction

Ideal for Back-up Battery on Low-Voltage Kits

BATTERY, 12V 9aH
Order Code #10-014

Enclosures available to house  multiple Batteries

20% MORE Power

AGM - Absorbed Glass Matt Construction
Longer-lasting; Faster re-charge

Ideal for Solar Applications

BATTERY, 12V 20aH
Order Code #10-099

Enclosures available to house  multiple Batteries

Suits HEAVY DUTY CYCLE

AGM - Absorbed Glass Matt Construction
Longer-lasting; Faster re-charge

Ideal for Heavy Duty Cycles &/or Accessories

RACK, 4-down
Order Code #11-015

Steel-reinforced Nylon Gear Rack in 1m lengths; Domestic application

Industry-standard, Steel-reinforced Nylon 'Gear Rack' in 1m lengths; 12.5mm wide at top w/ 4 downward-facing attachment points; Needs 50mm clearance to any Rear Support Post

Attaches along full length of gate (approx 80-90mm above ground level) to enable Motor's Pinion Gear to drive Gate open & closed

As above, except heavier duty for commercial applications; 25mm wide at top w/ 6 downward-facing attachment points

Pressed Galvanised Steel Track in 3m length approx 16mm high

Can be ground-mounted on existing concrete pad, brick pavers or steel beam. Hammer-in 'Zipfix' Fasteners typically used  to secure (18/length).
Note: Do not mount directly onto bitumen

Hammer-in 'Zipfix' Fasteners typically used  to secure Ground-mounted Track; 18 Fasteners required per 3m length of Track

Note: Do not mount Track directly onto bitumen

Pressed Galvanised Steel Track in 3m length approx 80mm high; Designed to be pre-set 60mm into new concrete driveway

Ideal for heavy traffic Commercial applications, or decorative pebble-mix driveways

Galvanised Steel Pin used to join & align multiple lengths of Concrete-in Track

Designed to run on Track (either Bolt-down or Concrete-in); Heavy Duty 300kg capacity per wheel = 600kg gate weight

Recesses neatly into 100x50mm RHS Bottom Rail of Sliding Gate

Top Rollers used to support Gate; typically 2 used; 1 either side of Top Rail of Gate

As above, except heavy duty

Supports 1 x Top Roller per Bracket

Supports 2 x Top Rollers per Bracket.

Mount on receiving Post to receive & locate Gate to prevent possibility of Intruders lifting Gate to 'walk-in'

Also available in 75mm width

Mounts on concrete at full open position.

Prevents gate running out of Roller support and falling over.

Steel reinforced Rubber Ground Stop
For use on heavy or clad Double Gates

Typically mounted in centre of driveway for firm closure of Double Gates;  especially on Gates 2m or more per side

Mechanical Assembly of Zinc-Plated Steel Parts
Ideal for Single-swing, Tubular Steel Farm Gates to 4.5m

Holds Gate fast against physical bracket to prevent inadvertent damage to Gate, Motor, Arms or Fixings by livestock (or Visitors!) forcing the gate

'Flipper Latch' releases automatically when Gate opens; Attaches with simple 'U' Bolts

12/24V DC Side-Throw Solenoid-activated Lock w/ Key-release for emergency exit

Typically used to lock single Swing Gates closed for greater security

Consistent swing & max 10mm gap to Striker Plate required for effective operation

12/24V DC Side-Throw Solenoid-activated Lock w/ Key-release for emergency exit

Typically used to lock single Swing Gates closed for greater security

Consistent swing & max 10mm gap to Striker Plate required for effective operation